Chiller service, maintenance and installation in Kocaeli and Sakarya
ABF İklimlendirme Sistemleri services chillers in Kocaeli and Sakarya, including factories in the organised industrial zones (OSBs) of Gebze, Dilovası and Çayırova. Our own team handles planned maintenance, breakdown repair, refrigerant and compressor work, design and installation, for process cooling in production plants and central air conditioning in hotels, hospitals and office buildings.
If a chiller breakdown stops your production in Kocaeli, Sakarya, İstanbul or Yalova, call us. We prioritise urgent breakdowns, and calls that stop production come first.
What is a chiller?
A chiller is a central cooling unit that chills water, or a water and glycol mixture, and pumps it through pipework to fan coil units, air handling units or production machines. Glycol is an antifreeze added to the water where there is a risk of freezing. Chillers come in two main types, depending on how they reject heat.
Air-cooled chillers
These reject heat to the outside air with fans. They are usually installed on a roof or in an open area and do not need a cooling tower. Maintenance focuses on cleaning the condenser coils and checking the fans.
Water-cooled chillers
These are installed in a plant room and reject heat through a cooling tower or dry cooler. They can be efficient at large capacities, but need water treatment, condenser heat exchanger cleaning and cooling tower maintenance.
What we do
Design and equipment selection
We calculate the cooling load, water temperatures, flow rate and redundancy needs, then design the unit and the hydronic (chilled water) circuit.
Installation and commissioning
We install the chiller, pump sets, pipework, expansion and control connections, and commission the system.
Planned maintenance
Condenser and heat exchanger cleaning, refrigerant pressures, compressor operating values, water flow, pumps and filters, plus control and alarm tests.
Breakdown repair
On-site diagnosis and repair of compressor, refrigerant circuit, fan, pump, flow switch and control faults.
Refrigerant and compressor work
Leak detection, vacuum and refrigerant charging after repair, compressor replacement and test runs.
Assessment of existing systems
For old or inefficient systems, we take measurements and compare repair, refurbishment and replacement options for you.
Which industrial zones do we cover?
Chillers are most common in production plants that need process water or mould cooling. Our chiller maintenance and breakdown service covers GOSB and the surrounding OSBs in Gebze, the chemical and machinery specialised OSBs in Dilovası, TOSB in Şekerpınar, Çayırova, the Sakarya 1. OSB in Arifiye and the Sakarya 2. OSB in Hendek. We also cover the other districts of Kocaeli, and schedule jobs in İstanbul and Yalova according to distance.
Our emergency breakdown service covers Kocaeli, Sakarya, İstanbul and Yalova, and chiller breakdowns that stop production are prioritised. Planned maintenance is scheduled around your production programme and, where possible, during planned shutdowns. For the wider HVAC needs of your plant, see industrial HVAC for factories and warehouses.
Outside Kocaeli and Sakarya, we also travel to production plants in Bursa, Bilecik, Düzce and Bolu for chiller maintenance, installation and other planned work. In these provinces we plan the work in advance; for a breakdown, we agree a day and time with you. Our emergency breakdown service covers Kocaeli, Sakarya, İstanbul and Yalova.
How often should a chiller be serviced?
Service intervals depend on the manufacturer's instructions, annual operating hours and site conditions. A pre-season and end-of-season check is the basic routine at most sites; process chillers that run continuously need more frequent checks.
What we check during planned maintenance
- Condenser coil or heat exchanger cleaning
- Refrigerant pressures and leak checks
- Compressor operating values, current and oil condition
- Water flow, temperature difference, pumps and filters
- Flow switch, sensors, control and alarm tests
- Electrical panel connections and protection devices
Every visit is logged in a service record.
Winter preparation and glycol
If water freezes in outdoor pipework or heat exchangers, they can be damaged. Circuits at risk of freezing are filled with a water and glycol mixture; the ratio depends on the lowest operating and ambient temperatures. Before winter, we measure the glycol ratio and check the frost protection settings and any circuits that are out of use.
Chiller faults: alarm codes, pressure, compressor and refrigerant
Alarm codes
Alarm codes differ by manufacturer and model, so the manufacturer's manual applies. Send a photo of the code on the display and the unit's nameplate via WhatsApp. Do not reset the alarm again and again to force the unit to run; this can damage the compressor.
Low-pressure alarm
This is often caused by low refrigerant or a leak, low water flow, a blocked filter or a fouled evaporator heat exchanger. The expansion valve and sensors are checked as well. Refrigerant is not added until the cause is found.
Compressor faults
Warning signs include a compressor that will not start, short cycling, protection devices tripping, unusual noise or overheating. We measure the power supply, protection devices, pressures and oil condition; any replacement decision follows these measurements.
Refrigerant charging
Falling refrigerant pressure means there is a leak in the circuit. We find and repair the leak before charging. After the repair, the system is evacuated, charged with the correct amount of refrigerant and test-run.
Where are chillers used?
Factories and process cooling
Cooling of moulds, machines or process water in plastic injection moulding, food, chemical and machinery manufacturing.
Hotels and hospitals
Central chilled water for many rooms and common areas; in hospitals, continuous operation and a redundancy plan.
Shopping centres and office buildings
Central air conditioning with air handling units and fan coil units.
Ships
We also install and service marine chiller systems. See marine A/C installation and service.
Chiller or VRF?
Chillers suit process cooling and large sites that need chilled water. VRF (variable refrigerant flow) is a system in which one outdoor unit group serves many indoor units through refrigerant piping, with each zone controlled separately. For offices, hotels and residential buildings where zone control matters, VRF is often the more flexible choice.
If you need refrigerated storage for products, see cold storage installation and service.
Frequently asked questions about chillers
How quickly can you respond to a chiller breakdown?
In Kocaeli, Sakarya, İstanbul and Yalova we prioritise urgent breakdowns: those that stop production, affect patient safety or shut down a critical area come first, and we set off as soon as possible. Travel time depends on distance and workload.
How often should a chiller be maintained?
It depends on operating hours, site conditions and the manufacturer's recommendations. More frequent checks may be needed at the start of the season and during heavy use. We prepare the maintenance plan together with you for your site.
Can you inspect our existing chiller?
Yes. We measure operating values, review the fault history and maintenance records, and report on the condition of the system and the priority work.
Why does the glycol ratio matter?
In circuits that run at low temperatures or are exposed to frost outdoors, glycol stops the water from freezing. The ratio is set by the lowest operating and ambient temperatures and is checked during maintenance.
Do you serve factories in Gebze, Dilovası and Çayırova?
Yes. We cover all districts of Kocaeli, including the organised industrial zones in Gebze, Dilovası and Çayırova, and Sakarya for chiller maintenance and breakdown service.
There is an alarm code on the chiller display. What should I do?
Send a photo of the code and the unit's nameplate via WhatsApp, or call us on +90 532 213 78 66. Because code meanings vary by manufacturer and model, we assess it together with you. Do not keep resetting the alarm to force the unit to run.
Chiller survey for your plant
Tell us how the chiller is used, which system you have and what the problem is. We will inspect it on site and agree the scope with you.